Présentation des actions de modélisation menées à Sollac Florange en vue de la conduite automatique des skin-pass = Development of mathematical models for automatic control of the temper mills at Sollac FlorangeBRESSON, P.Revue de métallurgie (Paris). 1992, Vol 89, Num 11, pp 1007-1014, issn 0035-1563Conference Paper

La topomaintenance au département Tôle fine de Sollac Florange = TPM at the sheet department of Sollac FlorangeADNET, P; OTTENWAELTER, G.Revue de métallurgie (Paris). 1996, Vol 93, Num 7-8, pp III-VII, issn 0035-1563, 11 p.Conference Paper

PROZESSDIAGNOSE IM KALTWALZWERK = PROCESS DIAGNOSIS IN COLD ROLLING MILLSWOERNER R.1980; BBC-NACHR.; DEU; DA. 1980-12; VOL. 62; NO 12; PP. 504-510; BIBL. 2 REF.Article

STUDY AND DEVELOPMENT OF A DEVICE FOR THE DETECTION OF SURFACE DEFECTS ON STEEL STRIP IN A SKIN-PASS ROLLING MILL = ETUDE ET MISE AU POINT D'UN DISPOSITIF DE DETECTION DES DEFAUTS DE SURFACE SUR DES BANDES D'ACIER LAMINEES SUR UN LAMINOIR SKIN-PASSDE JONGE MWC.1982; ; LUX; LUXEMBOURG: OFFICE FOR OFFICIAL PUBLICATIONS OF THE EUROPEAN COMMUNITIES; DA. 1982; EUR/5994/CCE/6210-60-6-601; 47 P.; 30 CM; TECNICAL STEEL RESEARCH: MEASUREMENTS AND ANALYSISReport

ANTRIEBSREGELUNGEN UND AUTOMATISIERUNG EINER ZWEIGERUESTIGEN DRESSIERSTRASSE = DRIVE CONTROL AND AUTOMATION SYSTEMS OF A TWO-STAND DRESSING LINEHUEGLE K; ORLOWSKI P.1980; BBC-NACHR.; DEU; DA. 1980-05; VOL. 62; NO 5; PP. 159-167; BIBL. 2 REF.Article

CORRECTION OF SHAPE DEFECTS IN A ROLLED SHEET BY LEVELLINGGRIGORYAN GG; GUROV AS.1981; IZV. VYSS. UCEBN. ZAVED., CERN. METALL.; ISSN 0368-0797; SUN; DA. 1981; NO 11; PP. 59-63; BIBL. 6 REF.Article

L'ECROUISSAGE HUMIDE AU SKIN-PASS DE 80" DES LAMINOIRS A FROID DE SOLLAC = WET WORK-HARDENING IN 80" SKIN-PASS OF SOLLAR'S COLD ROLLING MILLCOLLARD JF.1981; REV. METALL. (PARIS); ISSN 0035-1563; FRA; DA. 1981; VOL. 78; NO 12; PP. 955-960; ABS. ENG/GER/SPAArticle

Development of a skin pass preset model by using artificial intelligent methodsRENDUELES, J.-L; GONZALEZ, J.-A; DE COS, F.-J et al.Revue de métallurgie (Paris). 2004, Vol 101, Num 3, issn 0035-1563, vi,vii,viii,x,243-251 [13 p.]Conference Paper

Utilization of the pressure in hydraulic drives of cold rolling millsZHENIN, V.A; REDKIN, E.V.Vestnik mašinostroeniâ. 1984, Vol 64, Num 3, pp 38-40, issn 0042-4633Article

Modélisation mécaniques du laminage skin-pass = Mechanical modelling of temper rolling processONNO, F; GRATACOS, P.Revue de métallurgie (Paris). 1992, Vol 89, Num 10, pp 889-891, issn 0035-1563Article

Modernization of cold rolling mills = Modernisierung von KaltwalzwerkenDORFER, J.G.Iron and steel engineer. 1986, Vol 63, Num 10, pp 13-22, issn 0021-1559Article

Utilisation de techniques neuromimétiques en laminage à froid au skin-pass de Sollac Florange = Using neural network in cold rolling process at Sollac Florange temper millBRESSON, P; COURIOT, E; ALEXANDRE, F et al.Cahiers d'informations techniques de la revue de métallurgie. 1993, Vol 90, Num 7-8, pp IV-VI, 10 p.Conference Paper

On-line shape measurement and control for a 2-stand temper mill = On-line-Planheitsmessung und -regelung an einem zweigeruestigen KaltnachwalzwerkSWANSON, K.R; GRUBE, B.B; MCCLARIN, R.Q et al.Iron and steel engineer. 1986, Vol 63, Num 10, pp 29-35, issn 0021-1559Article

Déploiement de la topomaintenance à Sollac Desvres = Development of TPM at Sollac DesvresBLOQUEL, D; DELATTRE, J. C; DENQUIN, J. C et al.Revue de métallurgie (Paris). 1996, Vol 93, Num 10, pp iv-v, issn 0035-1563, 7 p.Conference Paper

Application of the preliminary displacement principle to the temper rolling modelLIU, Yuli; LEE, Won-Ho.KSME international journal. 2001, Vol 15, Num 2, pp 225-231, issn 1226-4865Article

DIE GLEICHSTROM-HAUPTANTRIEBE EINER ZWEIGERUESTIGEN DRESSIERSTRASSE = THE MAIN DC DRIVES OF A TWO-STAND SKIN PASS MILLGRUETZMACHER B; SCHROEDER D; WOERNER R et al.1981; BBC-NACHR.; DEU; DA. 1981; VOL. 63; NO 3; PP. 106-115Article

EXPERIMENTAL DETERMINING OF THE CONTACT ARE LENGTH BETWEEN THE BAND AND ROLL IN THE COLD ROLLINGVASILEV YA.1980; METALURGIYA; BGR; DA. 1980-04; VOL. 35; NO 4; PP. 10-13; BIBL. 10 REF.Article

ABHAENGIGKEIT DES PROFILS DER ARBEITSWALZEN VON DEN NACHWALZBEDINGUNGENSIMENOVA V.1982; METALURGIYA; BGR; DA. 1982-05; VOL. 37; NO 5; PP. 7-9; BIBL. 5 REF.Article

SHEET PROCESSING MINIMIZES AUTOMOBILE RUSTINGHOWKINS JE; BINGAMAN MJ.1981; IRON STEEL ENG.; USA; DA. 1981-02; VOL. 58; NO 2; PP. 66-69; BIBL. 5 REF.Article

RESULTATS DE SKIN-PASS OU DE PLANAGE SUR FER-BLANC = SKIN PASS OR LEVELLING OF TINPLATEPADWO Z.1981; REV. METALL. (PARIS); ISSN 0035-1563; FRA; DA. 1981; VOL. 78; NO 8-9; PP. 693-701; ABS. ENG; BIBL. 2 REF.Article

(CONTRIBUTION TO THE STUDY OF DEFORMATION OF EXTRAMILD STEEL THIN SHEETS BY SKIN-PASS ROLLING)NAGE A FROIDAMIOT BERNARD.1980; ; FRA; DA. 1980; 92 P.; 30 CM; BIBL. 51 REF.; TH. DOCT.-ING./REIMS/1980Thesis

KALTBANDWALZWERKE = COLD STRIP ROLLING MILLS1980; FACHBER. HUETTENPRAX. METALLWEITERVERARB.; DEU; DA. 1980-06; VOL. 18; NO 6; PP. 445-448Article

SURFACE QUALITY OF COLD ROLLED SHEETS FOR PRINTING MACHINESLIPUCHIN YU V; PIMENOV AF; BUTYLKINA LI et al.1981; STAL'; SUN; DA. 1981; VOL. 41; NO 11; PP. 54-57; BIBL. DISSEM.Article

MANUFACTURING OF HIGH CARBON STEEL STRIPS BY OPEN COIL ANNEALING AND SKIN PASS ROLLINGWADA Y; SHIRAISHI T; ONISHI T et al.1981; KAWASAKI SEITETSU GIHO; ISSN 0368-7236; JPN; DA. 1981; VOL. 13; NO 2; PP. 210-217; BIBL. 4 REF.Article

PROCESS CONTROL COMPUTERS AT ALTOS HORNOS DEL MEDITERRANEO COLD ROLLING FACILITYSNITKIN SR; KROFFT WH; CHATA AS et al.1981; IRON STEEL ENG.; USA; DA. 1981-08; VOL. 58; NO 8; PP. 25-32Article